HQMaster CNC Router Bits Straight Router Bit 1/8" Shank Straight Flute End Mill Cutter 2-Flute Milling Cutting for MDF PVC Acrylic Chipboard Wood 10 Pack

The media could not be loaded. I’ve had some pretty big disappointments when buying cutters and bits made in China. They were poorly made and dull out of the box.Not the case with this one.Thanks to the positive reviews on this cutter and the very reasonable price, I decided to give it one more try. I needed the cutters but didn’t want to pay the high price that Dremel wants for their version of the same thing.Right out of the box, I was impressed. They are well machined and very sharp.I used a single cutter on this entire project, to lower the depth of the lattice design 1/4”. The wood is Mimosa appx 10”x 15”. I did it in three passes, increasing the depth each time, for better control, to prevent tear out and to prevent overheating the cutter and dulling it.It cut clean, left no fuzz and a smooth, easy to sand finish. One cutter did the entire job and though I could tell right at the end it obviously wasn’t as sharp as it was in the beginning it was still doing a beautiful job and has some life left in it.Don’t be afraid to give them a try. Hopefully you will be as pleased as I am.

This is a good bit with some specializations. Run this on a Shapeoko with a Bosch 1617. Feeds at 100IPM with a 3/8" DOC at full RPM. Works extremely well on thin plywood (1/4") as you do not need tape to hold the board down, since the cutter will not pull up like it will with spiral flutes. On thicker materials, such as 3/4" ply, you will wind up with a layer of compressed sawdust holding the part in place, which makes cleanup a touch more difficult, as in some instances a screwdriver is required to separate the dust from the cut, but the edge quality is extremely good. Longevity is a tad short, like most of the HQMaster bits, sometimes the bit will go 10hrs or so of straight cutting before you notice signs of dulling (rougher edges, more RPM loss when cutting, etc) and sometimes they will shatter.

I purchased these because I had just purchased a dove tail jig from a high end woodworking retailer. The bit that came with it broke on first use. A replacement bit was $32. I just received these and finished my project. These worked perfectly and you just can't beat the price.

Seems to be well made blades. Due to the small size this type is difficult to sharpen correctly so I bout the ten pack so I'd always have sharp bits. I briefly used one of these and was happy with its ability to cut properly.

These are the only bits that i use.They last very well out of the bits that I have bought I have only broken one.I mainly use them on soft pine but have used them on Oak and other hardwood but I drive them extremely hard 100 ins per minute 30in/min down and .0032 each pass.They maintain their sharpness very well and I will get a production run of about 30 units per cutter. When I notice that the cut edge is becoming a little fuzzy I will change it out.As for the individual that complained that they were not 1/8 all the way down you have to have clearance down the sides of the cutter.It is not a fault of the cutter or the manufacturer it is by design.

It was pretty hard to see that this would not be a general purpose bit from the seller’s pictures , but on examination ( see the picture I included ), it’s clear that these bits arnt center cutting !That makes them much less useful for hobby or professional CNC users unless you are very careful to reduce your plunge rate, since these will have a hard time going straight down (vs side to side ). This is a bit of a critical flaw in these bits that makes them unsuitable for general purpose use sadly.

For the price these bits work great used them already. They do a great job I would recommend them.

Thought I would need all of these to route a 1/8" screen spline 1/4" deep in the oak door I built. Only did passes of 1/8 inch and went slow. Had my colt router on half speed too. Started slowing down towards the end but I was stubborn and wanted to see if I could make the bit last the whole job, IT DID. It was a little heat discolored at the end so threw it out. Still got 9 more!!Prob 16 feet of routing done with one bit. VERY GOOD!