TP-LinkEAP613 Wireless Access Point w/o DC Adapter | Ultra-Slim | Omada True Wi-Fi 6 AX1800 | Mesh, Seamless Roaming, WPA3, MU-MIMO | Remote & App Control | PoE+ Powered | Multiple Controller Options

Great little device. I had a defunct outlet box from an old house fan speed controller right in the middle of the 2nd story hallway slightly high on the wall and went, "Hmm, I wonder if they make a hotspot that goes on a wall box." Boom, they do. It works great. I have the power dialed down slightly to where it pretty much stays within the walls of the house and works on all floors (including attic, inhabited). So, plenty of power.

This is my second EAP615-Wall. I already have Omada Controller and needed this access point to broadcast 4 different SSID's, each on its own VLAN. Omada App sees these on the network immediately and once you adopt, setting the AP is very easy. If you already have a similar device, you can even copy the configuration. These provide good coverage for one room, it does not provide signal to the upper floors like Omada ceiling units, but works great if you want to increase coverage into one room.

Ease of setup and excellent build quality!

I've have a few tp-link Omada switches that run my home network and homelab. I have been using an Orbi mesh system in AP mode. It works great and never had issues, but I wanted to try and actual AP.At 8in, it's a little big but not too bad. It's very flat to the ceiling. The only issue with installation is the location of the Ethernet port. If you want the cable completely hidden you really need a slim Ethernet cable to go up into the ceiling, then a coupler on the cable to your run back to the switch. I recommend a 28AWG cat patch cable.It doesn't get too hot in my testing. I have a 2300sqft single story house and was able to put it almost in the middle. I have 1G Internet. The slowest speed through 4 walls, in the corner of the house is 600Mbps, which is fine. Latency is a little high at those far spots but good enough for wifi. Internally I can get 1.7Gbps using my phone which is crazy.The main takeaway here is this is a good AP for wifi 6 and you may only need one if you can get it in the center of your house.

Device worked great, concrete construction in Mexico didn't allow for repeaters to be used so I ran some cable, installed these with a poe switch on the other end, fyi depending on the distance of your cable run will determine the power needed from the power injector or switch. I bought one that self adjusts the port and was having some difficulty with the top floor which was about a 200 ft run so I set it to full power and it worked great. However the wifi device gets very hot. Not sure if I should be concerned or not but I opened a ticket with TP-Link. Have yet to hear back. Using the omada controller software was fairly easy but you have to have a dedicated device to run it or a computer on the same network which for some reason they kept losing the config so I went back to manual.

First, the minimal packaging was fantastic—eco-friendly and efficient. Installation and setup were a breeze, including the mesh configuration. The three Gigabit ports, including one PoE port, are a great feature. This AP solved my Wi-Fi issues without requiring an additional switch or PoE switch. Since I only needed to connect it to a Zigbee hub and a workstation, I replaced my five-port PoE switch with this AP. I simply moved the switch port to the PoE port to power the AP, and it worked perfectly.

Great access point and range for indoor use. The white status LED is not too bright at night and the 3 ports on the bottom are great for connecting additional devices if needed. Easy to mount to a standard single-gang electrical/data box.This was installed as part of an Omada deployment for a campground guest WiFi network that was replacing aging/outdated Ubiquiti equipment. Coupled with outdoor WiFi 6 EAP610s, these indoor units were used in trailers and campers that had weak signal from the outdoor units. Overall, these are great APs for short range needs like single rooms and small areas and works just fine. However, there is an overall flaw with all Omada APs regarding guest networking that was confirmed by TP-Link engineers that is important to note.TP-Link Omada access points of any flavor do not support Layer 2 client isolation. Even with guest network settings applied in the controller (or on the AP itself if using standalone), Layer 2 communication between clients still works despite not being able to ping those devices or reach any kind of a webpage or open port. While the guest settings do block the above types of client access, multicast packets still flow freely and everywhere. As such, our guest campground network let anyone anywhere wirelessly cast their screen via AirPlay, Google Cast, or Miracast to anyone's unsuspecting smart TV without warning. That is a huge security issue not to mention asking for problems to occur, so unfortunately I was left no choice but to return all of the Omada units and return to Ubiquiti equipment.With that being said, if that is not an issue for you, they work great in any other environment that does not require L2 isolation. they boot up incredibly quick, offer good signal and speed, and overall are a great product for the price. After escalating this issue with support, I was eventually put in touch with their engineering team running diagnostics with them and submitting Wireshark logs to get to the root of the problem. They said it would be added to a list for future firmware development, but I cannot wait for that to happen. It was upsetting to leave TP-Link because I know for a fact I would not get this kind of support with Ubiquiti (part of the reason I was trying to leave that ecosystem), but I didn't have much choice.